ADTRAN 6310 Manuel d'utilisateur télécharger pdf (Page 2)

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the

unit.

2. Connect the other end of the serial cable to the terminal or PC.

3. Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and

plug the cord into a standard electrical outlet. Refer to the NetVanta 6310/6330 Series Hardware

Installation Guide at https://supportforums.adtran.com

for more details.

4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud,

8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS CLI.

5. Enter enable at the > prompt. Enter the enable password when prompted. The default password is

password.

You can also access the CLI from a Telnet client. In order to do this, you must know the IP address of the AOS

device. If you do not know the unit’s IP address, you must use the CRAFT port to access the CLI. To access the

CLI using a Telnet client, follow these steps:

1. Connect the unit to your PC, using an Ethernet cable connected to ETH 0/1 port on the back of the unit.

2. Open a Telnet client on your computer. You can access the Telnet client by navigating to Start > Run and

entering telnet 10.10.10.1 (Windows® XP). If you are running Windows Vista, you will need to turn on the

Telnet client before you access it. To do this, navigate to Start > Control Panel > Programs and

Features > Turn Windows features on or off > Telnet Client Option and select OK. 10.10.10.1 is the

default unit IP address. If you have changed your unit’s IP address, you will need to enter that address.

3. Enter enable at the > prompt and enter the enable password when prompted. The default password is

password.

COMMON CLI COMMANDS

The following are common CLI commands and tips for getting started with the CLI.

• Entering a question mark (?) shows contextual help and options. For example, entering ? at the prompt

will show all commands available from that prompt.

• To view interface statistics, enter show interface <interface type> <interface number>.

• To view the current configuration, enter show running-config.

• To view all the IP addresses currently configured, enter show ip interface brief.

• To view the AOS version, serial number, and other information, enter show version.

• To save the current configuration, enter write.

CONFIGURE THE UNIT’S IP ADDRESS

The following steps create an IP address and subnet mask for ETH 0/1.

1. At the # prompt, enter config terminal.

2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for the Ethernet

port located on the rear of the unit.

3. Enter ip address 10.10.10.1

255.255.255.0 to assign an IP address to the Ethernet port using a 24-bit

subnet mask.

Many PCs do not come with a standard serial port. A universal serial bus (USB) to

serial adapter can be used instead. The drivers for the USB to serial adapter must be

installed according to the manufacturer’s instructions. If the USB to serial adapter is

not properly installed on your PC, you will not be able to communicate with the AOS

unit and you should seek support from the USB to serial adapter manufacturer.

The configuration parameters used in the examples outlined in this document are for

instructional purposes only. Replace all underlined entries (example

) with your

specific parameters to configure your application.

4. Enter no shutdown to activate the interface to pass data.

5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode.

6. Enter ip route 0.0.0.0

0.0.0.0 192.168.1.254 to add a default route to the route table. 0.0.0.0 is the default

route and the default subnet mask, and 192.168.1.254 is the next-hop IP address to which the AOS unit

should send all of its traffic. You will need to enter the proper route, subnet mask, and gateway for your

network. This information is typically provided by an Internet service provider (ISP) or local network

administrator.

7. Enter do write memory to save the current configuration.

ENABLE TELNET USER LOGIN ACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a

password of password.

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3. Enter login to initiate Telnet access.

4. Enter password adtran

to change the login password for the Telnet sessions.

5. Enter exit to return to the Global Configuration mode.

6. Verify that the prompt of your unit displays (config)#.

7. Enter do write memory to save the current configuration.

CONFIGURE YOUR APPLICATION

The applications you will need to configure vary by product and by network. Review the list of defaults for your

unit before deciding what applications to configure. The following are some common applications that should be

configured on startup. These are all available on ADTRAN’s Support Community

Configuring T1 Access to a Remote Site Using

PPP in AOS (video article 2003)

Configuring Internet Access (Many to One NAT) with

the Firewall Wizard in AOS (video article 2185)

Configuring Port Forwarding in AOS

(video article 2291)

Configuring QoS for VoIP in AOS

(video article 3091)

Configuring PPP in AOS (article 2523) Configuring HDLC in AOS (article 2152)

Configuring Frame Relay in AOS

(article 2350)

Configuring QoS in AOS

(article 1617)

Configuring DHCP Server in AOS

(article 2149)

Configuring a VPN Using Main Mode in AOS

(article 1925)

Configuring a VPN Using Aggressive Mode in

AOS (article 1926)

Configuring Voice Traffic over SIP Trunks in AOS

(article 3395)

Configuring the Switchboard and Dial Plan in

AOS (article 2130)

Configuring PRI Signaling for DSX-1 in AOS

(article 3396)

Configuring Enhanced ANI/DNIS Substitution

in AOS (article 2509)

Configuring Source and ANI Based Routing in AOS

(article 2510)

Important: For additional details on product features, specifications, installation,

and safety, refer to NetVanta 6310 Hardware Installation Guide at

https://supportforums.adtran.com

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

ADTRAN 6310 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau ADTRAN 6310